Fingerprint Sensor AS608 - A Beginner's Guide
One touch can replace keys. This project uses an optical fingerprint sensor to enroll users and then grant access with a quick scan.
read tutorial →
What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable shield goes onto your Arduino and provides a slim rechargeable power pack, with a built in battery charger as well as DC/DC booster.
Compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due - basically any Arduino-pinout-shaped Arduino as only the GND and 5V pins are used. You can stack shields on top, or stack the PowerBoost on top. Please note that the powerboost does not pass through the ICSP headers (the battery is in the way) so if your stacking shield uses ICSP for data transfer (like the Ethernet Shield), you'll need to stack the PowerBoost above it!
The PowerBoost shield can run off of any Lithium Ion or Lithium Polymer battery (3.7/4.2V kind) but we suggest our 1200mAh capacity or 2000mAh capacity batteries, both of which fits very nicely in the empty space of the shield. Plug in the battery and recharge it via the microUSB jack. When you're ready to go, just unplug the Arduino from USB or the wall adapter and it will automatically switch over to shield power. Use only Lipoly batteries with protection circuitry!
The onboard boost converter can provide at least 500mA current, and can peak at 1A. There's an onboard fuse to protect against higher current draws which could damage the boost converter or battery. The boost converter can be damaged by high current spikes and is not recommended for driving motors or robots where the stall current can cause high current spikes
The shield comes as a kit of parts, some light soldering is required to attach the stacking headers and switch! Battery is not included, but you can pick one up in the shop (again, we suggest our 1200mAh battery or 2000mAh battery, but you can use any 500mAh+ size you like) There's even an optional switch. If you choose to solder it in, it will let you turn the shield and Arduino power on/off.
TECHNICAL DETAILS
- Dimensions: 53mm x 69mm x 2mm / 2.1" x 2.7" x 0.08"
- Height w/ JST: 8mm / 0.3"
- Weight: 12.5g
Manila stock. Order before 16:00 PHT, ships today via J&T or LBC. Provincial: 1–3 working days.
Schools / class POs: we accept Purchase Orders for accredited schools and universities. contact us with your PO details.
Returns: 7-day inspection window for DOA units. Email proof of issue and we ship a replacement.
Customers also bought
Build with this board
Thumb Joystick - A Beginner's Guide
Wire a joystick to your Arduino, read X/Y, then print UP / DOWN / LEFT / RIGHT to the serial monitor.
read tutorial →Motor Drive (BTS7960 43A) - A Beginner's Guide
Bench-test a 43 A motor driver before wiring the full project. Catches weak power, mis-pinning, and dead boards before they cost you time.
read tutorial →Raspberry Pi Pico (RP2040) - A Beginner's Guide
Coming from UNO and the Pico won't show a COM port? Here's the BOOTSEL trick, the driver fix, and the first sketch that actually works.
read tutorial →Notes from the bench
Ask the community
Project Showcase — show what you built
Share what you built. Photos, BOM, what worked, what didn't.
view thread →How to ask a good question (and actually get answers)
Symptom + what you tried + clear photo = answers within hours.
view thread →ESP32 brownout when wiring a sensor — fixes that worked
Brownout reset when adding a sensor? Notes on supply decoupling and GPIO checks.
view thread →First Arduino — sketch upload error, what to try?
Upload failing on your first Uno? Driver, COM port, board match — checklist inside.
view thread →